How To Fix Windows Socket Error 10051 On Api Connect (Solved)

Home > Socket Error > Windows Socket Error 10051 On Api Connect

Windows Socket Error 10051 On Api Connect


COMMAND:> LIST STATUS:> Connecting ftp data socket WSAEADDRINUSE (10048) Address already in use Only one usage of each address is normally permitted. The error occurs with the socket() function, which takes the socket type (protocol) and address family as input parameters. A couple functions that the v1.1 specification missed are WSASetLastError() and WSAUnhookBlockingHook().

Berkeley description: This is a temporary condition and later calls to the same routine may complete normally (also known as EAGAIN error in Berkeley Software Distribution version 4.3) WinSock description: Same Microsoft C description: Too many open files. An asynchronous signal (such as SIGINT or SIGQUIT) was caught by the process during the execution of an interruptible function. Check that your network system (WinSock implementation) has a utility that shows network statistics. hop over to this website

Socket Error 10038

For example, the error can occur when an attempt is made to read from a file that is not open, to open an existing read-only file for writing, or to open This usually means the local software knows no route to reach the remote host." This is a network problem, and you should fix your network. This can help you (or your support staff) to zero-in on what's wrong when your application runs into a problem. WinSock description: Same as Berkeley.

  • WinSock functions: WSACancelAsyncRequest() Additional functions: Berkeley sockets connect() returns this error on subsequent calls, after an initial call on a non-blocking socket.
  • For more error code information, refer to Knowledge Base article 10140 at
  • Check your subnet mask.
  • On a datastream socket, the connection was reset.

WinSock functions: WSAETIMEDOUT (10060) Connection timed out. For example, you shouldn't necessarily expect to be able to use NS addresses with ARPA Internet protocols. Note that this error occurs rarely, because a Winsock implementation cannot reliably detect hardware problems.WSAENETUNREACH (10051) Network is unreachable A socket operation was attempted to an unreachable network. Socket Error 10049 Sometimes a 10061 error is caused by either a firewall or anti-virus software presence on the local computer or network connection.

As you can see from the comprehensive list of WinSock functions, this error is the catch-all. WSAEBADE (10009) Bad file numberA file descriptor argument was out of range, referred to no open file, or a read (write) request was made to a file that was only open Typically, though, WinSock generates this error when it receives a "host unreachable" ICMP message from a router. If you are using a router, verify the router is up and running (check by pinging it and then ping an address outside of the router).

You are unlikely to encounter them. Socket Error 11004 You cannot mix and match. (WINSOCK DLLs must be supplied by the same vendor that provided your underlying protocol stack).You cannot use more than one Winsock implementation simultaneously.If you have more You could use this to verify that you're receiving TCP resets or ICMP Port Unreachable packets each time you attempt to connect. If so, is there an older DLL in a directory in the path ahead of the directory containing the newer DLL?

Socket Error Codes Linux

WinSock functions: WSAEFAULT (10014) Bad address. WSAEINVAL (10022) Invalid argument. Socket Error 10038 This error occurs if the sin_addr is INADDR_ANY (i.e. Socket Error 10054 Connection Reset By Peer User suggestions: Some network systems have commands to report statistics.

What is Wilson's theorem? WinSock functions: recv(), recvfrom(), send(), sendto(), FD_CLOSE Additional functions: Any function that does I/O on the network could generate this error. A function fails with WSAEAFNOSUPPORT if the address family referenced in sockaddr is not compatible with the referenced socket's protocol. In fact, when you connect out, i.e. Socket Error 10053

Berkeley description: A message sent on a socket was larger than the internal message buffer or some other network limit. This may indicate the file was deleted on the NFS server or some other catastrophic event occurred. No process may have more than a system-defined number of file descriptors open at a time. WinSock description: Same as Berkeley.

The specified socket parameter refers to a file, not a socket.WSAEDESTADDRREQ (10039) Destination address required A required address was omitted from an operation on a socket. Windows Socket Error Windows 10 It may also make explicit mention of other functions that can fail with this error. NFS is "network-related" in the strictest sense, but the Network File System protocol is an application protocol (i.e.

WinSock functions: connect(), sendto(), FD_CONNECT Additional functions: It seems odd that the v1.1 specification doesn't ascribe this error to the function bind().

a TCP reset received from remote host). This has no network-relevant analog (although the "inode" reference could refer to a network file system entry). However, some WinSocks fail with WSAEINVAL you call connect() a second time (or subsequent) on a non-blocking socket. Winsock Error 10054 Fix This error occurs if you specifically reference a protocol that isn't part of the address family you also reference.

However, it also occurs when an application passes an invalid pointer value. recv() & recvfrom(): socket not bound (for Dgram) or not yet connected (for Stream), or the requested length is zero (whether a length >32K is acceptable as a non-negative value is For instance, if the length of a struct sockaddr is not equivalent to the sizeof(struct sockaddr). Not implemented: Name server does not perform specified operation.